Large user touch panel - convenient operation: The MKC-710S titrator comes with a large TFT colour touch screen. The MKC-710S is ideally suited to measure samples which only release their water slowly or at elevated temperatures: It can remote control the ADP-611 evaporator and visualize the evaporation curve on the display and printout.
A new acceleration amplifier provides faster electrolysis with a maximum electrolytic speed of 2.6 mg H2O/min. This shortens the time required for pre-titrations and sample measurements considerably.
Paper saving and environmentally friendly – results no longer need to be printed: Measurement results are converted to PDF and can be stored in a USB flash drive.
Two different user levels let you easily define the operation permissions of each operator. An administrator (protected with password) has access to all functions whereas a normal operator can only perform burette operation, calibration, measurement, method number (sample file) change and reading of method.
The MKC-710S coulometric Karl Fischer Titrator can be equipped with a titration cell with a replaceable ceramic diaphragm. It is thus the ideal solution to measure dirty and sticky samples with a low water content as eg. oils.
The MKC-710S is ideally suited to measure samples which only release their water slowly or at elevated temperatures: It can remote control the ADP-611 evaporator and visualize the evaporation curve on the display and printout. This allows to define all the measuring parameters including the purge cycles and the temperature in the evaporator in one single method and simplifies method development.
Transmitting sample weights directly from a balance, inputting sample names with a barcode reader, entering sample codes with a numeric keypad: The MKC-710S titrator offers all the interfaces and features required for a seamless integration into your workflow.
ASTM D 4928-11
ASTM E 1064-08
EN ISO 12937:2002-03
ASTM D 4928-11
|Type and model name||
MKC-710S Coulometric Karl Fischer Moisture Titrator
MCU-710S + MKC-710, IDP-100 Printer, Manual Solvent Change Unit
120 freely assignable methods
Karl Fischer Coulometric Titration
|Measuring range||Water content / Bromine Index||10 μg … 300 mg (depending on reagent)|
|Precision||Relative standard deviation
(Based on KEM's standard measuring conditions and standard liquids)
|< 0.3% (n=10)|
|Display Resolution||0.1 μg|
With or without diaphragm
Constant current pulse time control
|Endpoint detection||Polarized twin Pt electrode (AC)|
EP is detected when the drift is getting stable or when a preset limit time for the titration has been reached,
|Solvent quantity required||Anolyte
|100 mL (max. 150 mL)
8.4 inch color LCD 800 x 600 dots touch screen
|Calculations||Water content, statistics (mean, SD and RSD) and automatic averaging of blank values|
|Data storage||On board memory:||500 results|
Up to 10 operators can be registered.
Alert when Anolyte or Catholyte needs to be replaced
Reminder of scheduled check date, record of check results.
Operating hours counter.
RS-232C, 4 channels
for dot matrix printer, electronic balance, evaporator, Data Capture Software (SOFT-CAP)
for USB flash drive, thermal printer, keyboard, barcode reader, foot switch, USB hub
| 5 … 35 °C
< 85% (no condensation)
|Power supply||AC 100 … 240 V ±10 % 50/60 Hz (comes with AC adapter)|
|Power consumption||Main unit
|Dimensions||Touch panel controller
Solvent Change Unit:
|225(W) × 190(D) × 42(H) mm
141(W) × 292(D) × 244(H) mm
107(W) × 206(D) × 340(H) mm (without Solvent Change Unit)
240(W) × 140(D) × 405(H) mm (without tubing)
106(W) × 180(D) × 88(H) mm
|Weight||Touch panel controller
Solvent Change Unit:
|approx. 1.5 kg
approx. 3.0 kg
approx. 2.0 kg
approx. 0.6 kg
approx. 0.4 kg
|Conformity standard||CE marking EMC : EN61326-1 LVD: EN61010-1|
The Data Capture Software is an easy to use and flexible solution to collect measurement results from different KEM instruments (Refractometers, Density Meters, Potentiometric or Karl-Fischer Titrators, Thermal Conductivity Meters) on a Windows personal computer.
|Computer||Personal computer with Pentium II CPU of 233MHz or better|
|Operating system||Microsoft Windows 2000, XP,
Vista (Home Basic, Business), 7 (Home Premium, Professional)
|Other programs||Microsoft EXCEL 97 / 2000 / 2003 / 2007|
|RAM||at least 128 MB / 512 MB recommended|
|Hard disc space||10 MB required for installation|
|Display||Resolution higher than 640 * 480|
|Disk drive||CD-ROM or DVD-ROM|
|Interface||1 USB port
RS-232C D-sub (male) 9 pin required for each additional instrument
to be connected to the same computer.
Dot matrix ink printer for GLP compliance.
The ADP-611 substantially broadens the application spectrum of your Karl Fischer Titrator. With this evaporator accurate water determinations of samples which cannot be titrated directly can be performed:
The ADP-611 features a modern microprocessor control ensuring maximum precision, reliability and user-friendliness:
To safely avoid contamination from atmospheric moisture the ADP-611 is equipped with a remote controlled motor driven magnetic bar to move the sample from the sample chamber into the oven.
The heating chamber is equipped with an electrically conductive transparent heater glass. This permits the sample condition to be monitored during the vaporization process.
The ADP-611 comes with two built-in desiccant tubes for the carrier gas. With an optional air pump, air instead of nitrogen can be used as carrier gas.
|Technical Specifications ADP-611|
|Heating system||Electrically conductive transparent heating glass|
|Temperature control||Control method
Temperature measurement precision
50 … 300 °C
± 2 °C
|Display||Temperature or flow, LED, 3 digits|
|Heating tube||Pyrex® glass tube||30 (ø) x 335 (L) mm|
|Sample boat||Pyrex® glass
|68 (L) x 25 (W) x 15 (H) mm
|Carrier gas||Nitrogen (not included in supplied parts)
Air (air pump optional)
Gas flow rate
100 … 300 mL/min
|Gas dryer||Zeolite 100 g 2 pcs (500 g Zeolite included in supplied parts)|
|Interface||RS-232 9 pin male for communication with KF titrator|
|Ambient conditions||Temperature: 5 … 35°C
Humidity: < 85% RH
|Power||Supply (set in factory)
|100 … 120 V, 200 … 240 V AC, 50/60 Hz
|Dimensions||370 (W) x 195 (D) x 217 (H) mm|
|Weight||100 … 120 V version
200 … 240 V version
|approx. 5 kg
approx. 7 kg
Direct contact with Karl Fischer Reagents should always be avoided. This automatic filling an emptying system for the titration cell (ordering number 98-433-0135) protects operators from direct contact with toxic reagents and vapors. The pump is built into the magnetic stirrer. The connecting cable for the stirrer is included in the standard delivery.
|20-040-4200-48||Transparent cell with drain cock (glass cell only)|
|12-006-7300-48||Transparent cell, complete, including generator electrode without diaphragm, twin Pt electrode, washing bottle, funnel, KF grease, septum (10 pcs.) and anode adjuster|
|12-006-7400-48||Transparent cell, complete, including generator electrode with diaphragm, twin Pt electrode, washing bottle, funnel, KF grease, septum (10 pcs.) and anode adjuster|
|12-006-6200-48||Transparent cell, including generator electrode without diaphragm and twin Pt electrode|
|12-006-6100-48||Transparent cell, including generator electrode with diaphragm and twin Pt electrode|
|12-006-6300-48||Transparent cell with drain cock, including generator electrode without diaphragm and twin Pt electrode|
|12-006-6400-48||Transparent cell with drain cock, including generator electrode with diaphragm and twin Pt electrode|
|98-740-3011||Bent-type sampler for powders (1 … 1.5 mL)|
|98-740-3020||"C" bent-type sampler for powders|
|98-740-3025||Light weight sampler for powders|
|98-740-3026||Straight type light weight sampler|
|98-740-3030||Sampler for viscous products|
|98-740-3031||Sampler for highly viscous products|
|98-433-4013||Liquefied gas sampler with pressure vessel made of stainless steel (100 mL)|
|98-740-3013||Sampler for oils|
|98-740-3012||Spoon type sampler for viscous products|
|98-740-3024||Eggplant type sampler for powders|
|Syringe (5 mL)
Syringe (20 mL)
|98-433-3407||Stopper for syringe inlet port|